LUBRIPLATE "SYNAC 150, 220 & 320” SERIES

LUBRIPLATE SYNAC 150, 220 & 320 Series products are diester based synthetic fluids formulated to meet a multitude of demanding applications where traditional petroleum based lubricants may not be desirable. These diester based synthetic fluids are outstanding lubricants for applications in which the fluid is subjected to high temperature and high stress conditions over extended drain intervals. The extended drain interval capabilities of LUBRIPLATE SYNAC Series make them a very cost effective solution for your lubricant needs.

The LUBRIPLATE SYNAC 150, 220 & 320 Series make excellent lubricants for vacuum pumps, blowers, gear boxes, centrifuges and chains.

LUBRIPLATE Division strongly recommends the use of the FREE LUBRIPLATE Oil Analysis Program to establish extended drain intervals. This allows you to establish proper change out intervals and still maintain effective lubrication of your equipment. Typical service life can be from 2,000 to 8,000 hours depending upon operating conditions. Fluid life can be affected by various contaminants, moisture, temperature and other factors. Therefore, oil analysis becomes critical when maximizing useful service life. Contact your authorized LUBRIPLATE Distributor for more information on the FREE LUBRIPLATE Oil Analysis Program.

Advantages offered by LUBRIPLATE SYNAC Series include the following:

 Excellent High Temperature Stability and Oxidation Resistance = Extended Lubricant Life

 Very Low Deposit Forming Tendencies = Clean Operation

 Excellent Demulsibility Characteristics = High Separator Efficiency

 High Flash Point and Low Pour Point = Wide Operating Temperature Range

 Outstanding Anti-Wear Protection

 Foam Suppression Properties

 Corrosion Inhibitors

 Excellent Rust Protection

LUBRIPLATE SYNAC Lubricants are compatible with other LUBRIPLATE products such as LUBRIPLATE AC Oils, LUBRIPLATE HO Oils, and LUBRIPLATE SFGO Series Fluids. Always consult LUBRIPLATE before changing to a SYNAC fluid from an existing lubricant that may not be compatible with diester-based fluids. Conversion procedures from petroleum-based products are available upon request.

LUBRIPLATE SYNAC Lubricants are recommended for use with high nitrile Buna-N, Teflon, Viton, Fluorosilicone and polysulfide elastomers.

LUBRIPLATE SYNAC Lubricants are NOT recommended for use with low nitrile Buna-N, neoprene, natural rubber, styrene-butadiene rubber (SBR, Buna-S) or butyl rubber.

LUBRIPLATE "SYNAC 150, 220 & 320” SERIES - TYPICAL PROPERTIES

Physical Characteristics                     ASTM               SYNAC 150               SYNAC 220            SYNAC 320

Viscosity @ 100°F SUS                     D-445                754                             1003                         1496

@ 210°F SUS                                     D-445                71.3                             82.5                          99.1

@ 40°C cSt                                         D-445                147                              200.6                        290.1

@ 100°C cSt                                       D-445                12.6                            15.61                         20.04

Viscosity Index                                   D-2270              71                                74                             77

Pour Point °F/°C                                 D-97                  -25/-32                       -20/-29                       -5/-20

Flash Point °F/°C                                D-92                 540/282                       545/285                    475/246

Fire Point °F/°C                                  D-92                 570/299                       575/302                    505/263

API Gravity                                         D-287               15.8                            15.3                           17.3

Color                                                   D-1500             < 1.0                            < 1.0                         < 1.0

Density (Pounds/Gallon)                                              8.0                                8.03                           7.92

ISO Viscosity Grade                                                     150                              220                             320

Performance Characteristics

Four-Ball Wear Test                           D-4172              0.45                             0.45                            0.45

Average Wear Scar Diameter

(40 Kg., 1200 rpm., 1 hr. @ 75°C)

Copper Corrosion                               D-130                1a                                  1a                               1a

Conradson Carbon Residue                D-189                Nil                                 Nil                             Nil

Emulsion Characteristics @ 82°C    D-1401     43-37-0 (25)                  43-37-0 (25)              43-37-0 (25)

(Oil/Water/Emulsion)

Evaporation Loss                                D-972           3.0 Max.                       3.0 Max.                    3.0 Max.

(6.5 hours @ 204°C)

Rust Test Procedure B                    D-665  Pass, no corrosion         Pass, no corrosion       Pass, no corrosion

LUBRIPLATE SYNAC Oils are available in the following packaging:

Packaging Available                          SYNAC 150                 SYNAC 220                  SYNAC 320

5 Gallon Pail                                      L0936-060                   L0937-060                     L0938-060

55 Gallon Drum                                 L0936-062                   L0937-062                     L0938-062

                                                                                                                                       Printed in USA

                                                                                                                                       Revised 4-25-08