LUBRIPLATE SYN-H1-220

                                                                           *NSF H-1 Registered

                                                                  “This product is certified OU Kosher Pareve”

                                                                           “This product is Halal certified”

LUBRIPLATE SYN-H1-220 is a Polyalkylene Glycol (PAG) based synthetic, bearing and gearbox lubricant specifically designed for use where elevated temperatures exist and the need for a Food Grade lubricant is required. LUBRIPLATE SYN-H1-220 is specifically formulated for food processing equipment where there is the possibility of incidental food contact and is manufactured with ingredients which comply with FDA 21 CFR 178.3570 and NSF H-1 requirements.

LUBRIPLATE SYN-H1-220 is recommended for bearings and gearboxes that are exposed to temperatures up to 400°F for extended periods of time.  With its excellent load carrying capacity, 12 Stages Passed on FZG Four Square Gear Test, you can be assured that your bearings and gears have the utmost protection from wear even under the most severe operating conditions. LUBRIPLATE SYN-H1-220 has excellent lubricity which decreases friction and lowers bulk oil temperatures.  It also has outstanding thermal and oxidative stability which allows for its longer service life.

 Typical Tests

 Viscosity SUS @ 100°F (calculated)                                1310

  cSt @ 40°C                                                                       252

 Viscosity SUS @ 210°F (calculated)                                188

  cSt @ 100°C                                                                     40.7

 Viscosity Index                                                                  212

 Color                                                                                  L-0.5

 ISO Grade                                                                          220 / 320

 API Gravity                                                                       9.44

 Flash Point °F/°C                                                               >540 / >282

 Pour Point °F/°C                                                               -20 / -29

 FZG Four Square Gear Test

     Stage Passed                                                                  12

 Turbine Oil Rust Test

     ASTM D-665 (A & B)                                                 Pass

(Over for additional details)

Elastomer Compatibility

LUBRIPLATE SYN-H1-220 is compatible with most elastomers used in seals and gaskets.  Below is a list of the most common elastomers which are suitable for use with LUBRIPLATE SYN-H1-220. 

Viton Butyl Rubber Natural Black Rubber

 Kalrez Buna S Natural Red Rubber

 Silicone Buna N Natural Gum Rubber

 Polysulfide Hycar Neoprene

 EPR Hypalon

Changeover Procedure for LUBRIPLATE SYN-H1-220:

LUBRIPLATE SYN-H1-220 is compatible with minor amounts of petroleum oils.  However, to achieve maximum performance from LUBRIPLATE SYN-H1-220, it is suggested that the following procedure be followed when converting from petroleum oil based lubricants in a reservoir system such as bearing housing or gearbox:

1.  Drain previous lubricant from equipment while still warm.

2.  Replace any filter if applicable.

3.  Fill equipment reservoir with LUBRIPLATE SYN-H1-220.  Run under normal operating conditions for 24  hours. LUBRIPLATE SYN-H1-220 will generally clean any varnish and sludge which may have been left  behind by the

petroleum oil.

4.  Thoroughly drain the reservoir while still warm.

5.  Inspect the oil filters, if applicable, and replace as needed.

6.  Fill the reservoir with fresh LUBRIPLATE SYN-H1-220 and begin normal operation

LUBRIPLATE SYN-H1-220 is available in the following:

 Packaging Available                                       Part No.

 5-gallon Pail                                                    L0779-060

 55-gallon Drum                                               L0779-062

*NSF H-1 Registration No.                             138317  

(Meets USDA 1998 Guidelines)

*Authorized by NSF for use in food processing facilities as a lubricant or anti-rust agent on

equipment in which there may be incidental contact involving the lubricated part and the edible product.

*NSF - National Sanitation Foundation

     Printed in USA

     Revised 4/21/08