Hung’s International Inc. U.S.A
To fully take advantage of our speciality & practical experience of machine lubrication,to save your money,time & energy !
HTCL FG-68, FG-220 100% H-2 Synthetic Chain Oil
LUBRIPLATE HTCL-FG 220 & HTCL-FG 68
LUBRIPLATE HTCL-FG 220 & LUBRIPLATE HTCL-FG 68 are 100% ester based synthetic fluids specifically designed for use on oven chains in food manufacturing operations where incidental food contact is a possibility. The combination of an ashless additive system and the synthetic ester base provide protection against wear, rust, oxidation and corrosion. These products are approved under NSF H1 classification.
LUBRIPLATE HTCL-FG 220 & LUBRIPLATE HTCL-FG 68 are recommended for use on bakery oven chains, drying
oven chains, tenter frame chains, heat-treating chains, paint curing oven chain applications where they are exposed to high
operating temperatures and must maintain a clean lubricated surface.
LUBRIPLATE HTCL-FG 220 & LUBRIPLATE HTCL-FG 68 can be fed through micro lube systems, spray systems,
mist systems, drip bottle systems and can be hand applied. When lubricating a hot chain, position the lubricator at the
coolest point on the chain and use the minimum volume necessary to properly lubricate the chain. This will help prevent
smoking of the lubricant once it reaches the hottest point in the oven.
Benefits of LUBRIPLATE HTCL-FG 220 & LUBRIPLATE HTCL-FG 68 are as follows:
Eliminates carbon build-up on chains
Does not contain harmful VOC’s which pollute the atmosphere
Advanced ester chemistry reduces friction, wear and energy costs
High auto-ignition temperature to reduce the risk of oven fires >700ºF
Superior film strength reduces oil consumption and reduces smoke
Tests HTCL-FG 220 HTCL-FG 68
Viscosity @ 40ºC 223.8 68.2
Oven Test at 150ºC
Vis Change 24 hrs 226 68.9
Vis Change 48 hrs 229 70.9
Vis Change 72 hrs 247 72.3
Vis Change 96 hrs 264 74.6
Vis Change 120 hrs 270 74.6
TAN Change 24 hrs 0.12 0.11
TAN Change 48 hrs 0.21 0.15
TAN Change 72 hrs 0.22 0.20
TAN Change 96 hrs 0.23 0.23
TAN Change 120 hrs 0.26 0.28
Flash Point ºC 302 302
Evaporation Loss 204ºC/24 hours 2.05 2.45
TGA Wt Loss 250ºC 0.13 0.23
Panel Cooker, 600ºF, Residue, mg 18 13
4-Ball Wear Test 40 Kg, 600 rpm, 180ºC 0.48 0.48
Viscosity @ 100ºC cSt 19.6 10.7
Block On Ring COF 0.09 0.09
Ramsbottom, Carbon Residue 0.06 0.06
Specific Gravity @ 60ºF
Appearance Clear, Pale Liquid Clear, Pale Liquid
MAJOR APPLICATIONS INCLUDE:
Textile - Tenter Frame Chains
Wallboard - Dryer Chains
Painting - Dryer Chains
Lithographic Chains - Beverage Can Lines
Glass - Forming Line Chains
Laminating - Drying Lines
Food Cookers & Frying
Heat Treating - Chains & Bearings
Kiln Support Rollers - Cement Plants (Trunions)
Bakery Oven Chains
HOW TO APPLY AND AT WHAT TEMPERATURE
Micro Lube Systems +/- 500ºF
Spray Systems +/- 500ºF
Mist Systems +/- 500ºF (Fire Safety precautions are necessary with this system when exposed to open flame).
Drip Bottle Systems +/- 500ºF
Drip Bottle With Brush +/- 500ºF
Hand Applied +/- 500 ºF (Apply @ 250ºC or less to minimize smoke. Also run chain a few minutes to remove excess).
Note: To avoid heavy smoke, lube in small volumes with more frequency. The higher the temperature, the more important this
Where to lubricate a chain - (Lubricator positioning is important)
Lube chains on slack side whenever possible.
Lube at pin and roller (Pin Bush Joint).
When lubing a hot chain, position the lubricator at the coolest point or as close as possible.
Note: Know and understand the source of the heat to avoid fires. If you are in doubt, contact Technical Services at,
Our suggestion for establishing the lube cycle for automatic chain lubricators is to base it on amperage draws (an increase in
friction). A simple high amp setting, activating a solenoid, signaling the lube motor (present for lube duration) to turn on. If you
have any problems with systems of this nature, contact one of our Technical Staff.
Remember to advise your customer that this chain oil contains an ester and when first applied to a used chain, he may experience
a heavy cleaning action and must deal with dirt, contaminants and rust coming off the used chain. This will last +/- two weeks and then the only thing coming off the chain will be a soft carbon when used in maximum temperature range.
HTCL-FG 220 HTCL-FG 68
*NSF H1 Registration No. 143870 143869
(NSF H1 - Authorized by NSF (National Sanitation Foundation) for use in food processing facilities as a lubricant or anti-rust agent on equipment in which there
may be incidental contact involving the lubricated part and the edible product.)
HTCL-FG 220 HTCL-FG 68
Packaging Available Part No. Part No.
Ctn. 4/1 Gallon Jugs L0947-057 -------------
5 Gallon Pail L0947-060 L0946-060
55 Gallon Drum L0947-062 L0946-062
Printed in USA