Hung’s International Inc. U.S.A
To fully take advantage of our speciality & practical experience of machine lubrication,to save your money,time & energy !
PGO-FGL Series 100% H-1 Synthetic Lubricant
LUBRIPLATE PGO-FGL SYNTHETIC GEAR OILS
ISO Viscosity Grades 150, 220, 320, 460 & 680
*NSF H-1 Registered
“These products are certified OU Kosher Pareve”
“Approved by Flender”
The LUBRIPLATE PGO-FGL grades consist of a range of ISO VG lubricants formulated to provide the user with superior performance under demanding operating conditions. Water soluble polyalkylene glycol base stocks, known to provide outstanding micropitting and EP characteristics are used to manufacture these lubricants. With the addition of a high performance, food approved additive package, these products are able to offer excellent thermal stability, high wear reduction rates, high micropitting resistance and load carrying ability as well as good corrosion protection.
Suitable Application Areas
The LUBRIPLATE PGO-FGL ranges have been specially formulated for use as industrial gearbox lubricants within the food manufacturing environment. As such, they have achieved approval within a number of different gear designs, these include:
When changing from a mineral oil or PAO based product to one of the LUBRIPLATE PGO-FGL grades, the following procedure should be followed:
The system should be run until the old oil is warm, then drain as fully as possible, particular attention being paid to reservoirs, lines etc., where oil may be trapped. The system should be cleaned of residual sludge.
Flush the system with the minimum quantity of LUBRIPLATE PGO-FGL by operating under no load and then drain the system while the fluid is warm. Repeat if necessary.
Seals, etc., should be inspected and if deteriorated, then replaced. Seals previously exposed to other oils may shrink when exposed to LUBRIPLATE PGO-FGL fluids, therefore, it may be advantageous to replace them, however, this is not mandatory. Careful inspection of the system for leaks will often suffice.
It is useful to inspect the lubricant after one or two days in use to make sure that it is free of extraneous materials. Contamination with significant quantities of other lubricants can, in some cases, lead to sludging, foaming and other problems.
LUBRIPLATE PGO-FGL Synthetic Gear Oils - Cont’d:
Polyurethane based elastomers, leather, cork, asbestos, paper and board should be avoided. Common seal and gasket materials are unaffected by LUBRIPLATE PGO-FGL Synthetic Gear Oils. Nitrile Rubber (NBR), FluoroSilicone or Vinyl-Methyl Polysiloxane (Q) are recommended especially where high temperatures are involved.
Ordinary industrial paints soften in the presence of these products. Internal gearbox surfaces should ideally be unpainted, or coated with resistant materials, for example a resistant two-pack epoxy formulation. These products must never be mixed with mineral or PAO based products.
Typical tests for LUBRIPLATE PGO-FGL Synthetic Gear Oils are as follows:
Typical Tests PGO-FGL150 PGO-FGL 220 PGO-FGL 320 PGO-FGL 460 PGO-FGL 680
Viscosity @ 40°C 150 227 339 477 725
Viscosity @ 100°C 25 41.9 60.6 83 122.2
ISO Viscosity Grade 150 220 320 460 680
Viscosity Index 232 242 252 262 272
Pour Point - 47ºC - 42°C - 39ºC - 36°C - 33ºC
Flash Point (COC) 284ºC 284°C 282ºC 284°C 287ºC
Density @ 15°C (Kg/L) 1.057 1.057 1.062 1.067 1.072
TAN 0.2 Max 0.2 Max 0.2 Max 0.2 Max 0.2 Max
FZG Load Stage
A/8.3/90 ----- >12 ----- >12 -----
FZG Load Stage ----- 10 ----- ----- - ----
@ 90 °C Endurance ----- 10 ----- ----- -----
FZG Load Stage ----- 10 ----- ----- -----
@ 60 °C Endurance ----- 10 ----- ----- -----
4-Ball Wear Scar
(40 Kg., 1 Hr.) 0.32 mm 0.34 mm 0.38 mm 0.38 mm -----
(ASTM D972) 0.26% 0.36% 0.13% 0.22% -----
(Continued) LUBRIPLATE PGO-FGL Synthetic Gear Oils - Cont’d:
Packaging Available PGO-FGL-150 PGO-FGL 220 PGO-FGL 320 PGO-FGL 460 PGO-FGL 680
54-Gallon Drum L0810-062 L0811-062 L0812-062 L0813-062 L0815-062
5-Gallon Pail L0810-060 L0811-060 L0812-060 L0813-060 L0815-060
Carton, 4/1 Gallon Jugs L0810-057 L0811-057 L0812-057 L0813-057 L0815-057
*These products are authorized by NSF for use in food processing facilities as a lubricant or anti-rust agent
on equipment in which there may be incidental contact involving the lubricated part and the edible product.
PGO-FGL 150 PGO-FGL 220 PGO-FGL 320 PGO-FGL 460 PGO-FGL 680
*NSF H1 Registration No’s 141192 141193 141194 141195 141196
(Meets USDA 1998 Guidelines)
*NSF – National Sanitation Foundation
Manufactured with ingredients that comply with FDA 21 CFR 178.3570.
"The LUBRIPLATE PGO-FGL Series contain no components derived from TSE/BSE relevant animal
species, therefore, they are compliant with the requirements of the TSE Note for Guidance EMEA/410/01
Rev. 2, October 2003".
Printed in USA